Duct Layout and Routing

A well-designed duct layout and routing ensure:

1.Efficient airflow: minimizing pressure drops and energy losses

2.Reduced noise: optimizing duct placement and design

3.Easy maintenance: accessible ducts for cleaning and repairs

Design Considerations

1.Space constraints: navigating obstacles and tight spaces

2.Duct sizing: ensuring adequate airflow and pressure drop

3.Fittings and connections: minimizing losses and turbulence

4.Support and hangers: securing ducts properly

Best Practices

1.Minimize bends and elbows: reducing pressure drops

2.Use gradual transitions: optimizing airflow and pressure

3.Avoid duct routing near heat sources: preventing damage and energy losses

Design Tools

1.CAD software: creating detailed duct layouts

2.HVAC design software: simulating airflow and pressure drop

Comments

VALVES USED IN A CHILLER SYSTEM AND THE TYPICAL VALVE PACKAGE

VALVES USED IN A CHILLER SYSTEM AND THE TYPICAL VALVE PACKAGE 1.Chilled Water Side Valves ⇒Isolation valve (manual/electric actuated). ⇒ Installed on CHW supply and return lines. ⇒ Used to isolate chiller for maintenance. 2. Balancing Valve (Manual or Automatic) ⇒ Ensures correct flow rate to/from chiller. ⇒ Helps maintain Delta T and proper flow distribution. ⇒ Located after evaporator outlet (return line). 3. Differential Pressure Bypass Valve (if 2-way valves in system) ⇒ Prevents excess pressure build-up when terminals shut. ⇒ Maintains flow through chiller. 4. Flow Switch ⇒ Senses chilled water flow across evaporator. ⇒ Safety interlock: trips chiller if flow is lost. ⇒ Usually paddle type or electronic. 5. Air Vent Valve (Manual or Automatic) ⇒ Removes air pockets. ⇒ Placed at high points of piping and chiller headers. 6. Drain Valve ⇒ For flushing, cleaning, and maintenance. ⇒ Located at low poin...

HVAC MEP Thumb Rules & Formulas (With Examples)

HVAC MEP Thumb Rules & Formulas (With Examples) 1. Heat Load Calculation Formula: Q = Area (sq.ft) x Heat Load Factor (BTU/hr per sq.ft) Example: 500 sq.ft office: Q = 500 x 30 = 15,000 BTU/hr TR = 1.25 2. CFM Calculation Formula: CFM = Sensible Heat (BTU/hr) / (1.08 x Delta T) Example: 12,000 BTU/hr, Delta T = 20°F CFM = 556 3. AHU/FCU Sizing Rule: 1 TR = 400 CFM 2 TR Airflow = 800 CFM 4. Duct Sizing Velocity Limits: Main: 1400-1800 FPM 800 CFM @ 1000 FPM 0.8 sq.ft 14"x10" 5. Chilled Water Flow Rate Formula: GPM = BTU/hr / (500 x Delta T) Example: 24,000 BTU/hr GPM = 4.8 6. Pipe Sizing 1" pipe: 8-12 GPM 2" pipe: 30-40 GPM 35 GPM Use 2" 7. Chiller Sizing Formula: TR = BTU/hr / 12,000 Example: 60,000 BTU/hr → 5 TR 8. Cooling Tower Sizing Rule: Heat Rejection = 1.25 x Load 10 TR → Tower = 12.5 TR 9. Pump Head Calculation Formula: Power (kW) = (Q x H x 9.81) / (Efficiency x 1000) Example: Q = 5 L/s, H = 20 m, Efficiency = 0.75 Power 1.31 kW 10. Fresh Air Re...

Understanding "Approach" in Chiller Systems: Causes, Impacts, and ASHRAE-Based Best Practices

Understanding "Approach" in Chiller Systems: Causes, Impacts, and ASHRAE-Based Best Practices In chiller system performance, one critical parameter that is often overlooked but highly indicative of system health is the Approach Temperature. What is Approach? Approach refers to the temperature difference between: Evaporator Approach: Leaving chilled water temperature vs. refrigerant evaporating temperature Condenser Approach: Leaving condenser water temperature vs. refrigerant condensing temperature A low approach indicates efficient heat transfer, while a high approach signals performance degradation. ASHRAE Guidance What is a "Good" Approach? Based on industry best practices and references from ASHRAE: Evaporator Approach (Typical Range): 1-3°C (1.8-5.4°F) →Excellent / Clean condition 3-5°C (5.4-9°F) → Acceptable, monitor trend > 5°C (9°F) →Indicates fouling or performance issue Condenser Approach (Typical Range): 2-4°C (3.67.2°F) →Good performance 4-6°C (7.2-...

HVAC engineers

Search This Blog