HVAC system components

Here are the common components of an HVAC (Heating, Ventilation, and Air Conditioning) system:

Heating Components:

1. Furnace (gas, oil, electric)

2. Boiler (hot water, steam)

3. Heat Pump (air-source, ground-source)

4. Radiant Floor Heating

5. Heat Exchanger (coils, tubes)

Cooling Components:

1. Compressor

2. Condenser Coils

3. Evaporator Coils

4. Expansion Valve

5. Refrigerant

Ventilation Components:

1. Fans (supply, exhaust, return)

2. Vents (intake, exhaust, transfer)

3. Ductwork (supply, return, exhaust)

4. Air Filters (particulate, gas, odor)

5. Controls (thermostats, humidistats, sensors)

Air Handling Components:

1. Air Handler Unit (AHU)

2. Fan Coil Unit (FCU)

3. Blowers

4. Coils (heating, cooling)

5. Plenums

Control Components:

1. Thermostats

2. Humidistats

3. Sensors (temperature, humidity, pressure)

4. Controllers (PID, PLC)

5. Valves (control, isolation)

Other Components:

1. Pumps (circulating, condensate)

2. Motors (fan, compressor)

3. Drives (variable speed)

4. Insulation

5. Duct Sealants

Note: The specific components may vary depending on the type of HVAC system and its application.

Comments

VALVES USED IN A CHILLER SYSTEM AND THE TYPICAL VALVE PACKAGE

VALVES USED IN A CHILLER SYSTEM AND THE TYPICAL VALVE PACKAGE 1.Chilled Water Side Valves ⇒Isolation valve (manual/electric actuated). ⇒ Installed on CHW supply and return lines. ⇒ Used to isolate chiller for maintenance. 2. Balancing Valve (Manual or Automatic) ⇒ Ensures correct flow rate to/from chiller. ⇒ Helps maintain Delta T and proper flow distribution. ⇒ Located after evaporator outlet (return line). 3. Differential Pressure Bypass Valve (if 2-way valves in system) ⇒ Prevents excess pressure build-up when terminals shut. ⇒ Maintains flow through chiller. 4. Flow Switch ⇒ Senses chilled water flow across evaporator. ⇒ Safety interlock: trips chiller if flow is lost. ⇒ Usually paddle type or electronic. 5. Air Vent Valve (Manual or Automatic) ⇒ Removes air pockets. ⇒ Placed at high points of piping and chiller headers. 6. Drain Valve ⇒ For flushing, cleaning, and maintenance. ⇒ Located at low poin...

HVAC MEP Thumb Rules & Formulas (With Examples)

HVAC MEP Thumb Rules & Formulas (With Examples) 1. Heat Load Calculation Formula: Q = Area (sq.ft) x Heat Load Factor (BTU/hr per sq.ft) Example: 500 sq.ft office: Q = 500 x 30 = 15,000 BTU/hr TR = 1.25 2. CFM Calculation Formula: CFM = Sensible Heat (BTU/hr) / (1.08 x Delta T) Example: 12,000 BTU/hr, Delta T = 20°F CFM = 556 3. AHU/FCU Sizing Rule: 1 TR = 400 CFM 2 TR Airflow = 800 CFM 4. Duct Sizing Velocity Limits: Main: 1400-1800 FPM 800 CFM @ 1000 FPM 0.8 sq.ft 14"x10" 5. Chilled Water Flow Rate Formula: GPM = BTU/hr / (500 x Delta T) Example: 24,000 BTU/hr GPM = 4.8 6. Pipe Sizing 1" pipe: 8-12 GPM 2" pipe: 30-40 GPM 35 GPM Use 2" 7. Chiller Sizing Formula: TR = BTU/hr / 12,000 Example: 60,000 BTU/hr → 5 TR 8. Cooling Tower Sizing Rule: Heat Rejection = 1.25 x Load 10 TR → Tower = 12.5 TR 9. Pump Head Calculation Formula: Power (kW) = (Q x H x 9.81) / (Efficiency x 1000) Example: Q = 5 L/s, H = 20 m, Efficiency = 0.75 Power 1.31 kW 10. Fresh Air Re...

Type of Heat Exchanger

There are several types of heat exchangers used in HVAC systems, including: 1. Coil Type: - Chilled water coils - Hot water coils - DX (direct expansion) coils - Evaporator coils - Condenser coils 2. Shell and Tube Type: - U-tube heat exchangers - Straight tube heat exchangers 3. Plate Type: - Plate and frame heat exchangers - Plate and shell heat exchangers 4. Finned Tube Type: - Finned tube heat exchangers 5. Spiral Type: - Spiral heat exchangers 6. Regenerative Type: - Regenerative heat exchangers 7. Adiabatic Type: - Adiabatic wheel heat exchangers 8. Run-Around Coil Type: - Run-around coil heat exchangers These heat exchangers are used in various applications, including: - Air conditioning - Heating - Ventilation - Refrigeration - Heat recovery - Industrial processes Each type of hea...

HVAC engineers

Search This Blog